Click to enlarge

SOFT COMPOUND FOR SMOOTH RIDE AND GRIP ON HARD DIRT TRACKS

sold each -- sorry wheels not included

Cheng Shin Tire 18-9.50-8 Mowku 4ply Tl

IN THIS PICTURE OF AN ATC70, THERE IS NO SEAT OR FENDER LIFT KIT

SO THIS TIRE WILL GO ON A 8" RIM AND HAVE ENOUGH CLEARANCE !!!

These Are a 4 Ply Rated Tire.

THEY CAN BE TUBED OR TUBELESS (RATED TUBELESS)TL

Tread is approximately 3/16 inch

Corners Are around, Just Right for Sliden The Curve's

*********************************************************

PLEASE TAKE NOTE !!!!!!!!!!!!!!!!!

ALL TIRES MUST BE SHIPPED "UPS_GROUND" AND TO THE LOWER 48 STATES ONLY. PLEASE CHOOSE "UPS_GROUND" WHEN ORDERING TIRES OR WE WILL HAVE TO CANCEL YOUR ORDER. SORRY BUT TOO MUCH TROUBLE WITH SHIPPING THEM ANY OTHER WAY...

********************************************************

@ NEW!! CS_Mowku_4ply ROUNDED_EDGE FLAT_TRACK_TIRES 18X9.50X8 FITs_STOCK_FENDER (sold_each) 1/21S (18_950_8) 18-950-8

@ e * "TRICK" ATC70_REAR_HUB FOR_ADDING 8" WHEELS_WITH 110MM_BOLT_PATTERN  (SOLD_EACH)  42410-HF1-A00 1/22A  (264E)@ e * "TRICK" ATC70_REAR_HUB FOR_ADDING 8" WHEELS_WITH 110MM_BOLT_PATTERN (SOLD_EACH) 42410-HF1-A00 1/22A (264E)THESE HUBS WILL FIT RIGHT ON THE STOCK REAR ATC70 AXLE AND ALLOW YOU TO USE ANY 4 ON 110 BOLT PATTERN WHEEL.

THE 4 ON 110 IS THE MOST COMMON BOLT PATTERN FOR THE LARGER HONDA ATV'S

THESE HUBS DO HAVE 10MM STUDS WHICH ARE PRESSED IN AT THE FACTORY AND ARE REPLACEABLE, IF NEEDED.

These will fit the following and probably more models of ATC's

ATC70 1978 to 1985 (checking 1973 and 74 yet)

All ATC 90s (except balloon tire models).

All ATC 110s

All ATC 125s

All ATC 185s

All ATC 200s

All air cooled, ATC 250Rs

264E
@ Extenders/spacer for hubs with 4 on 110 mm bolt pattern  (263Q)@ Extenders/spacer for hubs with 4 on 110 mm bolt pattern (263Q)These can be used with our HUB102 hubs

(sold as set of two)

ALUMINUM REAR WHEEL SPACERS Die cast aluminum wheel spacers will add stability to your ATV!

Spacers add 5” (2-1/2” per side) to rear wheel track.

Kits include: two spacers and mounting hardware.

263Q
@ DWT BLUE LABEL ALLOY WHEEL  (8"_Dia_x_8"_Wide)  (bolt_pat_4_x_110mm) (3"x5"_offset)  (.125"_Thick)  (SOLD_EACH) (006-03) temp out of stock@ DWT BLUE LABEL ALLOY WHEEL (8"_Dia_x_8"_Wide) (bolt_pat_4_x_110mm) (3"x5"_offset) (.125"_Thick) (SOLD_EACH) (006-03) temp out of stockThese are a polished aluminum wheel. They do have an offset 3 inches on the inside 5 inches on the outside from the center.

PRE INSTALLED RUBBER VALVE STEM

006-03